We Recommend:
10 Top Car Audio Amplifiers Reviews:
- Power - 1100 Max x 1 @ 2 Ohms, 550 Max x 1 @ 4 Ohms
- Class A/B Topology - Class ‘A’ amplifiers have enormous amount of current flowing through its output transistors with no audio signal. Class ‘B’ amplifiers have no current flowing through its outputs with no audio signal
- Mosfet Power Supply - A MOSFET is an electrical switch that allows the flow of electrical current. It controls the output voltage & current precisely by removing the output current sensing loss & eliminating all secondary feedback circuitry
- Low & High Level Inputs - A low level (RCA) input is measured in voltages. A high level (+/- wire) input is measured in wattages. Both essentially carry signal from your receiver to your amplifier to your speakers
- Variable Low-Pass Crossover - Subwoofers reproduce sound based on a number of different low-range frequencies. You can set exact sound specifications for the bass frequency reproduction
- Class D MOSFET Monoblock Power Amplifier
- Peak Power at 1 Ohm: 1,600 Watts | RMS Power at 1 Ohm: 1,200 Watts
- Frequency Response: 20Hz - 250Hz, On-board Bass EQ Switch with +6 or +12dB boost at 45Hz
- Featuring 4-Way Protection Circuitry and 4 Gauge Power & Ground Input Terminals for Maximum Current Flow. Damping Factor - 150<
- Stable at 1 ohm | Remote Subwoofer Level Control Included
- Power - 3000 Watts Max x 1 @1-Ohm, 1500 Watts Max x 1 @2-Ohms
- Class D - Power loss is significantly reduced making the amplifier highly efficient. Excess energy is stored until it’s needed instead of being converted into heat. Reduction in size/weight, reduced power waste, smaller heat sink, compact circuitry
- 1 Ohm Stable - Able to continuously power loads of 1 Ohm without encountering difficulties such as overheating. Typically made to power up subwoofers that demand the heavier power load requirements to be able to perform the way they were made to
- Strapping Capable - You are able to strap TWO PL3000.1D amplifiers and double the power that is being sent to your subwoofer(s). You now have the ability to connect more subwoofers to take advantage of the extra power
- Variable Subsonic Filter - To prevent your subwoofer(s) from bottoming out, the variable subsonic filter filters out frequencies below the subwoofer(s) specified low frequency limits and allows the driver to reach a maximum safe excursion
- Power - 800 Watts Max x 2 @2-Ohms 400 Watts Max x 2 @4-Ohms 1600 Watts Max x 1 Bridged @4 Ohms
- Full Range - With a Full Range amplifier you not only have the option to run your speakers but also your subwoofers
- Class A/B Topology - Class ‘A’ amplifiers have enormous amount of current flowing through its output transistors with no audio signal Class ‘B’ amplifiers have no current flowing through its outputs with no audio signal
- Mosfet Power Supply - A MOSFET is an electrical switch that allows the flow of electrical current It controls the output voltage and current precisely by removing the output current sensing loss & eliminating all secondary feedback circuitry
- Variable Gain Control - The gain control is not for adjusting volume It simply adjusts the amount of signal that is coming from your receiver and going to your amplifier
- 5000 Watts
- 1 Channel
- 1 Ohm
- 8Hz to 250Hz
- Extreme Bass, Bass Boost, Subsonic filter, low pass
- Power - 550 Watts Max x 4 @2-Ohms, 275 Watts Max x 4 @4-Ohms, 1100 Watts Max x 2 Bridged @4 Ohms
- Class A/B Topology - Class ‘A’ amplifiers have enormous amount of current flowing through its output transistors with no audio signal. Class ‘B’ amplifiers have no current flowing through its outputs with no audio signal
- Full Range - With a Full Range amplifier you not only have the option to run your speakers, but also your subwoofers
- MOSFET Power Supply - A MOSFET is an electrical switch that allows the flow of electrical current. It controls the output voltage & current precisely by removing the output current sensing loss & eliminating all secondary feedback circuitry
- Variable Gain Control - The gain control is not for adjusting volume. It simply adjusts the amount of signal that is coming from your receiver and going to your amplifier
- Excellent for voice as well as bass
- 2 ohms
- 3000 watts
- Mono
- Bass boost
- Competition Grade SPL Class D Monoblock MOSFET Car Power Amplifier
- Peak Power at 1 Ohm: 4, 700 Watts | RMS Power at 1 Ohm: 3, 500 Watts
- Stable at 1 Ohm, Frequency Response: 15Hz - 270Hz
- Featuring 4-Way Protection Circuitry and 1/0 Gauge Power And Ground Input Terminals for Maximum Current Flow
- User Adjustable Low Pass Filter (Variable): 35Hz - 250Hz, Remote Subwoofer Level Control Included
- 1400 WATT POWER: The Pyle Dual Channel Car Amplifier is perfect for your vehicle's sound system. Gives you up to 1400W bridgeable output. Features switchable bass boost, variable gain control, configurable electronic crossover network
- GOLD-PLATED RCA PORTS: The RCA ports are gold-plated for eliminating signal loss. A subsonic filter allows low-end interference to be cut so your speakers will always deliver the highest quality audio. Features switchable bass boost, low level inputs
- MOSFET PULSE: The MOSFET pulse width modulation power supply allows for a clean, distortion-free signal to your compact speakers providing you with crisp and clear audio for an outstanding music experience. Also features anti-thump turn on
- THERMAL PROTECTION: To keep both your car and the stereo amp safe, this model is equipped w/ thermal, overload and short circuit protection. Has been specially designed from the bottom up to provide safe and high quality sound in a sturdy form factor
- SLIM SIZE DESIGN: This box amp's small size makes installation a breeze - you'll have no trouble finding a spot for this little yet powerful device. Additional features include LED indicators, RCA outputs, soft turn-on circuit, remote turn on/off
- 750 watt maximum power full-range amplifier
- Amplifier Class: AB
- No. of channel: 2/1 Channel
- Max. Output Power: 750W x 2
Last update on 2022-03-19 / Affiliate links / Images from Amazon Product Advertising API